Standard Operating Procedure Provisioning XGPON ALU 7360 ISAM PT. Lintas Teknologi Indonesia Menara MTH 16 th Floor Jl. MT Haryono Kav. 23 Jakarta 12820 - Indonesia Telp. +62 21 8378 0000 Fax. +62 21 8378 0001 http://www.lt-indonesia.com 2013
Standard Operating Procedure Provisioning
XGPON ALU 7360 ISAM
PT. Lintas Teknologi Indonesia
Menara MTH 16th
Floor Jl. MT Haryono Kav. 23 Jakarta 12820 - Indonesia
Telp. +62 21 8378 0000
Fax. +62 21 8378 0001
http://www.lt-indonesia.com 2013
XGPON ALU 7360 ISAM Provisioning SOP 2
Sta
nd
ard
Op
era
tin
g P
roce
du
re
DOCUMENT CONTROL
Author : Rendi
Change Authority :
Revision History :
Version Number Date Issued Status Editor Reason for Change
1 26-10-2014 Draft Rendi Draft
Reviewers:
Name Organization Department Review Date
Approvals:
Name Organization Department Approval Date
Change Forecast: Low
Intellectual Property Rights This document contains valuable trade secrets and confidential information of ALU and its partners, and shall not be disclosed to any person, organization, or entity unless such disclosure is subject to the provisions of a written non-disclosure and proprietary rights agreement or intellectual property license agreement approved by ALU or LINTAS. The distribution of this document does not grant any license in or rights, in whole or in part, to the content, the product (s), technology, or intellectual property described herein.
XGPON ALU 7360 ISAM Provisioning SOP 3
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Table of Contents
DOCUMENT CONTROL 2
1. INTRODUCTION 6
2. PERSON IN CHARGE (PIC) 6
3. PROVISIONING 7
3.1 I-240W-A ONT 7 3.1.1 TOPOLOGY 7 3.1.2 CONNECTIONS AND COMPONENTS 7 3.1.3 CREATE/MODIFY/DELETE ONT 9 3.1.4 CREATE/MODIFY/DELETE INTERNET SERVICE (PPPoE) 9 3.1.5 CREATE/MODIFY/DELETE IPTV SERVICE 9 3.1.6 CREATE/MODIFY/DELETE VOICE SERVICE 10
3.2 O-16160E-Q ONT 11 3.2.1 TOPOLOGY 11 3.2.2 CONNECTIONS AND COMPONENTS 11 3.2.3 CREATE/MODIFY/DELETE ONT 13 3.2.4 CREATE/MODIFY/DELETE INTERNET SERVICE (BRIDGE) 13 3.2.5 CREATE/MODIFY/DELETE IPTV SERVICE 13 3.2.6 CREATE/MODIFY/DELETE VOICE SERVICE 14
3.3 B-2404-P ONT 15 3.3.1 TOPOLOGY 15 3.3.2 CONNECTIONS AND COMPONENTS 15 3.3.3 CREATE/MODIFY/DELETE ONT 17 3.3.4 CREATE/DELETE E1 SERVICE 17
3.4 POINT TO POINT (P2P) (NELT-B) 19 3.4.1 TOPOLOGY 19 3.4.2 CONNECTIONS AND COMPONENTS 19 3.4.3 CREATE/MODIFY/DELETE TAGGED VLAN SERVICE 22
4. APPENDIX: PROVISIONING FLOW 23
XGPON ALU 7360 ISAM Provisioning SOP 4
Sta
nd
ard
Op
era
tin
g P
roce
du
re
List of Figures FIGURE 1 PHYSICAL TOPOLOGY OF I-240W-A INDOOR ONT AT PT. TELKOM INDONESIA 7 FIGURE 2 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS (BACK VIEW) 7 FIGURE 3 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS (SIDE VIEW) 7 FIGURE 4 I-240W-A INDOOR ONT LEDS 8 FIGURE 5 PHYSICAL TOPOLOGY OF O-16160E-Q MDU ONT AT PT. TELKOM INDONESIA 11 FIGURE 6 PHYSICAL CONNECTIONS ON THE FRONT OF O-16160E-Q MDU ONT 11 FIGURE 7 PHYSICAL CONNECTIONS ON THE BACK OF O-16160E-Q MDU ONT 11 FIGURE 8 O-16160E-Q MDU ONT LEDS 12 FIGURE 9 PHYSICAL TOPOLOGY OF E1 SFP TO B-2404-P ONT AT PT. TELKOM INDONESIA 15 FIGURE 10 PHYSICAL CONNECTIONS FOR B-2404-P BUSINESS ONTS 15 FIGURE 11 B-2404-P BUSINESS ONT LEDS 16 FIGURE 12 PHYSICAL TOPOLOGY OF P2P AT PT. TELKOM INDONESIA 19 FIGURE 13 FRONT VIEW OF THE NELT-B 19 FIGURE 14 BOARD LEDS ON THE NELT-B 19 FIGURE 15 LEDS FOR SFP PORTS 20 FIGURE 16 PHYSICAL OF 1000BASE-LX SFP 20 FIGURE 17 CREATE ONT FLOW 23 FIGURE 18 MODIFY ONT SERIAL NUMBER FLOW 23 FIGURE 19 DELETE ONT FLOW 23 FIGURE 20 CREATE INTERNET SERVICE FLOW (PPPOE) 23 FIGURE 21 MODIFY SERVICE BANDWIDTH FLOW 24 FIGURE 22 MODIFY INTERNET PPPOE USERNAME AND PASSWORD FLOW 24 FIGURE 23 DELETE INTERNET SERVICE FLOW (PPPOE) 24 FIGURE 24 CREATE INTERNET SERVICE FLOW (BRIDGE) 24 FIGURE 25 DELETE INTERNET SERVICE FLOW (BRIDGE) 25 FIGURE 26 CREATE IPTV SERVICE FLOW 25 FIGURE 27 DELETE IPTV SERVICE FLOW 25 FIGURE 28 CREATE VOICE SERVICE FLOW 26 FIGURE 29 MODIFY POTS PORT FLOW 26 FIGURE 30 DELETE VOICE SERVICE FLOW 26 FIGURE 31 CREATE E1 SERVICE FLOW 27 FIGURE 32 DELETE E1 SERVICE FLOW 28 FIGURE 33 CREATE POINT TO POINT TAGGED VLAN FLOW 29 FIGURE 34 DELETE POINT TO POINT TAGGED VLAN FLOW 29
XGPON ALU 7360 ISAM Provisioning SOP 5
Sta
nd
ard
Op
era
tin
g P
roce
du
re
List of Tables TABLE 1 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS 8 TABLE 2 I-240W-A INDOOR ONT LEDS 8 TABLE 3 O-16160E-Q MDU ONT PHYSICAL CONNECTIONS 11 TABLE 4 O-16160E-Q MDU ONT LEDS 12 TABLE 5 B-2404-P BUSINESS ONT CONNECTIONS 15 TABLE 6 B-2404-P BUSINESS ONT LED DESCRIPTIONS 16 TABLE 7 LED DEFINITION FOR THE NELT-B 19 TABLE 8 BEHAVIOR OF LEDS FOR SFP PORTS 20 TABLE 9 OPTICAL PARAMETERS FOR ALCATEL-LUCENT APPROVED OPTICAL MODULES 21 TABLE 10 1000BASE-LX OPTICAL MODULE PARAMETERS 21
XGPON ALU 7360 ISAM Provisioning SOP 6
Sta
nd
ard
Op
era
tin
g P
roce
du
re
1. INTRODUCTION
This document has been prepared for reference of XGPON ALU 7360 provisioning at PT Telkom Indonesia.
2. PERSON IN CHARGE (PIC)
Name Company Phone Number Roles and Responsibilities
Rendi PT. Lintas Teknologi Indonesia
+62 82233167779 Senior Access Engineer
XGPON ALU 7360 ISAM Provisioning SOP 7
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3. PROVISIONING
3.1 I-240W-A ONT
3.1.1 TOPOLOGY
Figure 1 Physical topology of I-240W-A indoor ONT at PT. Telkom Indonesia
3.1.2 CONNECTIONS AND COMPONENTS
Figure 2 I-240W-A indoor ONT physical connections (back view)
Figure 3 I-240W-A indoor ONT physical connections (side view)
1st IPTV
I-240W-A ONT
Splitter 1:8
Home Connection
FTM
7360 ISAM FX OLT
Splitter 1:4
PON
Internet
SIP Phone
2nd
IPTV Eth#1
Eth#2
Eth#3
Eth#4
POTS#1
POTS#2
XGPON ALU 7360 ISAM Provisioning SOP 8
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Table 1 I-240W-A indoor ONT physical connections
Connection Description
Ethernet ports
This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100 Base-T Ethernet interfaces are supported. The Ethernet ports can support both data and in-band video services on all four interfaces.
Fiber optic This connection is provided through an SC/APC fiber optic connector.
LED button This buttons turns all LEDs on or off.
POTS This connection is provided through RJ-11 ports. Up to two POTS connections are supported. The POTS ports support voice services.
Wireless button Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using a Wireless button.
WPS button The Wi-Fi Protected Setup button is labeled WPS. This button enables and disables WLAN data encryption.
Power This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection.
USB ports This connection is provided through 2 USB ports.
Figure 4 I-240W-A indoor ONT LEDs
Table 2 I-240W-A indoor ONT LEDs
Indicator LED color and behavior LED behavior description
PWR Green solid Off
Operating on AC power No power source
Link Green solid Off
GPON link is OK GPON link is not OK
Auth Green solid Off
ONT is authorized ONT is not authorized
LAN 1 to 4 Green solid Off
Ethernet is linked ONT power off or Ethernet not connected
TEL 1 to 2 Green solid Green flashing Off
Off hook Call in On hook
VOIP Green solid Off
VOIP is OK VOIP is not OK
WPS Green solid Red Off
"In Progress" or "Success" status "Error" and "Session Overlap" status WPS not activated
WLAN Green solid Green flashing Off
Wireless enabled Traffic on wireless interface Wireless disabled
XGPON ALU 7360 ISAM Provisioning SOP 9
Sta
nd
ard
Op
era
tin
g P
roce
du
re
USB Green solid Green flashing Off
One or more USB device is connected One or more USB device is connected with traffic No USB device connected
INTERNET Green solid Off
HSI WAN is connected HSI WAN is not connected
3.1.3 CREATE/MODIFY/DELETE ONT
a. Create configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sw-ver-pland 3FE54869ACEC29
sernum <ONT-SERNUM> subslocid WILDCARD voip-allowed iphost cvlantrans-mode local
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/14 planned-card-type veip
plndnumdataports 1 plndnumvoiceports 0 admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/1 planned-card-type 10_100base
plndnumdataports 8 plndnumvoiceports 0 admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/2 planned-card-type pots
plndnumdataports 0 plndnumvoiceports 2 admin-state up
b. Modify ONT Serial Number configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sernum <NEW-ONT-SERNUM>
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up
c. Delete configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down
configure equipment ont no interface 1/1/<SLOT>/<PON>/<ONT>
3.1.4 CREATE/MODIFY/DELETE INTERNET SERVICE (PPPoE)
a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 upstream-queue 0 bandwidth-profile
name:<UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 queue [0...3] shaper-profile
name:<DOWN-BW>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/14/1 admin-up
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/14/1 max-unicast-mac 4
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/14/1 vlan-id 881 vlan-scope local network-
vlan <INTERNET-VLAN> single-tagged
configure veip ont 1/1/<SLOT>/<PON>/<ONT>/14/1 domain-name <PPPoE-USERNAME> admin-state up
configure ntp ont 1/1/<SLOT>/<PON>/<ONT> key <PPPoE-PASSWORD>
b. Modify Bandwidth configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 upstream-queue 0 bandwidth-profile
name:<NEW-UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 queue [0...3] shaper-profile
name:<NEW-DOWN-BW>
c. Modify PPPoE Username and Password configure veip ont 1/1/<SLOT>/<PON>/<ONT>/14/1 domain-name <PPPoE-USERNAME>
configure ntp ont 1/1/<SLOT>/<PON>/<ONT> key <PPPoE-PASSWORD>
d. Delete configure ntp ont 1/1/<SLOT>/<PON>/<ONT> no key
configure veip ont 1/1/<SLOT>/<PON>/<ONT>/14/1 no domain-name no admin-state
configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/14/1
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/14/1 no admin-up
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 queue [0...3] shaper-profile none
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 upstream-queue 0 no bandwidth-profile
3.1.5 CREATE/MODIFY/DELETE IPTV SERVICE
a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 upstream-queue 0 bandwidth-profile
name:<UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 queue [0...3] shaper-profile
name:<DOWN-BW>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/1/4 admin-up
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/1/4 max-unicast-mac 4
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/1/4 vlan-id 111
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/1/4 pvid 111
configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/1/4:111 max-num-group 2
configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/1/4:111 preview-packages "[1...1024]"
XGPON ALU 7360 ISAM Provisioning SOP 10
Sta
nd
ard
Op
era
tin
g P
roce
du
re
b. Modify Bandwidth
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 upstream-queue 0 bandwidth-profile
name:<UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 queue [0...3] shaper-profile name:<NEW-
DOWN-BW>
c. Delete configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/1/4
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/1/4 no admin-up
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 queue [0...3] shaper-profile none
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 upstream-queue 0 no bandwidth-profile
3.1.6 CREATE/MODIFY/DELETE VOICE SERVICE
a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 bandwidth-profile
name:VOIP_UP-1M
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile
name:VOIP_DN-1M
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip vlan-id <VOIP-VLAN> vlan-scope network
tag untagged
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip pvid <VOIP-VLAN>
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/vuni max-unicast-mac 2
configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 dhcp enabled vlan <VOIP-VLAN>
configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 admin-state up
configure voice ont voip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 protocol sip conf-method omci
configure voice ont sip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 proxyserv-prof 20
outproxyserv-prof 20 reg-expire-time 3600 re-reg-head-start 360 aor-host-prt-prof 21
registrar-prof 24 uri-format sip-uri dscp 46 opt-tx-cntrl disable
configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/1 user-aor <VOIP-USER1> user-
name <VOIP-USER1>@telkom.net.id display-name <VOIP-USER1> password <VOIP-PWD1> realm
telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13
configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/1 voipconfig sip voip-media-prof 3
admin-state unlocked
b. Modify POTS Number configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/1 admin-state locked
configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/1 user-aor <NEW-VOIP-USER1>
user-name <NEW-VOIP-USER1>@telkom.net.id display-name <NEW-VOIP-USER1> password <NEW-VOIP-
PWD1> realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13
configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/1 admin-state unlocked
c. Delete configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/1 admin-state locked
configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/1 user-aor none user-name none
display-name none password none realm telkom.net.id no ac-code-prof no app-serv-prof no
ntwk-dp-prof
configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/1 voip-media-prof none
configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/voip
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile none
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 no bandwidth-profile
XGPON ALU 7360 ISAM Provisioning SOP 11
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3.2 O-16160E-Q ONT
3.2.1 TOPOLOGY
Figure 5 Physical topology of O-16160E-Q MDU ONT at PT. Telkom Indonesia
3.2.2 CONNECTIONS AND COMPONENTS
Figure 6 Physical connections on the front of O-16160E-Q MDU ONT
Figure 7 Physical connections on the back of O-16160E-Q MDU ONT
Table 3 O-16160E-Q MDU ONT physical connections
Connection type Description
Management
The first management interface (MGMT) is a craft port where connection is provided through an RJ-45 connector. The second management interface (CONSOLE) is a craft port where connection is provided through an RJ-45 connector.
1st IPTV
O-16160E-Q ONT
Splitter 1:8
Connection
FTM
7360 ISAM FX OLT
Splitter 1:4
PON
Internet
SIP Phone
2nd
IPTV Eth#1
Eth#2
Eth#3
Eth#4
POTS#1
POTS#16
……..
ETH#16
……..
XGPON ALU 7360 ISAM Provisioning SOP 12
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Ethernet This connection is provided through an Ethernet RJ-45 cable. Up to 24 Ethernet connections are supported. The Ethernet ports support both data and in-band video services.
POTS For the O-24240E-Q, this interface is an RJ-21 connector with 48 positions which support up to 24 POTS lines. For the O-16160E-Q, this interface is an RJ-21 connector with 32 positions which support up to 16 POTS lines.
Fiber optic An SC/APC fiber optic connector terminates a fiber optic connection from the P-OLT.
dc power This connection is provided through an 8-pin UPS power connector.
grounding lug This connection is provided through a ground wire connected to the lug.
ac power This connection is provided by an ac power cord with a three-pronged female plug.
12 V battery backup This connection is provided by a power cord with a two-pronged female plug.
Figure 8 O-16160E-Q MDU ONT LEDs
Table 4 O-16160E-Q MDU ONT LEDs
LED name LED color LED behavior description
PWR Off Green
No power Power on
ALM Off Red
Normal System failure
NET Off Green
Optical path error 1490 nm data path (downstream) is OK and PLOAM has been exchanged with the OLT
MGMT Off Green
ONU is not register to OLT Full communication with ranging sync established between OLT and ONT
SIGN Off Green
VoIP not registered VoIP registered
RTP Off Green
All of the POTS ports on-hook One or more of the POTS ports off-hook
MODE Off Green
10M 100M
LINK Off Yellow Solid Yellow flashing
Link not up Link up Link up and Rx or Tx activity detected
XGPON ALU 7360 ISAM Provisioning SOP 13
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3.2.3 CREATE/MODIFY/DELETE ONT
a. Create configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sw-ver-pland 3FE53866AOCK26
sernum <ONT-SERNUM> subslocid WILDCARD voip-allowed iphost cvlantrans-mode local
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/10 planned-card-type 10_100base
plndnumdataports 8 plndnumvoiceports 0 admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/11 planned-card-type 10_100base
plndnumdataports 8 plndnumvoiceports 0 admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/2 planned-card-type pots
plndnumdataports 0 plndnumvoiceports 16 admin-state up
b. Modify ONT S/N (Serial Number) configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sernum <NEW-ONT-SERNUM>
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up
c. Delete configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down
configure equipment ont no interface 1/1/<SLOT>/<PON>/<ONT>
3.2.4 CREATE/MODIFY/DELETE INTERNET SERVICE (BRIDGE)
a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0
bandwidth-profile name:<UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-
profile name:<DOWN-BW>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> admin-up
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> max-unicast-mac 4
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> vlan-id <INTERNET-VLAN>
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> pvid <INTERNET-VLAN>
b. Modify Bandwidth configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0
bandwidth-profile name:<NEW-UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-
profile name:<NEW-DOWN-BW>
c. Delete configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> no admin-up
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-
profile none
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0 no
bandwidth-profile
3.2.5 CREATE/MODIFY/DELETE IPTV SERVICE
a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0
bandwidth-profile name:<UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-
profile name:<DOWN-BW>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> admin-up
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> max-unicast-mac 4
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> vlan-id 111
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> pvid 111
configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>:111 max-num-group 2
configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>:111 preview-packages
"[1...1024]"
b. Modify Bandwidth configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0
bandwidth-profile name:<UP-BW>
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-
profile name:<NEW-DOWN-BW>
c. Delete configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> no admin-up
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-
profile none
XGPON ALU 7360 ISAM Provisioning SOP 14
Sta
nd
ard
Op
era
tin
g P
roce
du
re
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0 no
bandwidth-profile
3.2.6 CREATE/MODIFY/DELETE VOICE SERVICE
a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 bandwidth-profile
name:VOIP_UP-1M
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile
name:VOIP_DN-1M
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip vlan-id <VOIP-VLAN> vlan-scope network
tag untagged
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip pvid <VOIP-VLAN>
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/vuni max-unicast-mac 2
configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 dhcp enabled vlan <VOIP-VLAN>
configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 admin-state up
configure voice ont voip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 protocol sip conf-method omci
configure voice ont sip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 proxyserv-prof 20
outproxyserv-prof 20 reg-expire-time 3600 re-reg-head-start 360 aor-host-prt-prof 21
registrar-prof 24 uri-format sip-uri dscp 46 opt-tx-cntrl disable
configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> user-aor <VOIP-USER1>
user-name <VOIP-USER1>@telkom.net.id display-name <VOIP-USER1> password <VOIP-PWD1> realm
telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13
configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> voipconfig sip voip-media-
prof 4 admin-state unlocked
b. Modify POTS Number configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> admin-state locked
configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> user-aor <NEW-VOIP-
USER1> user-name <NEW-VOIP-USER1>@telkom.net.id display-name <NEW-VOIP-USER1> password
<NEW-VOIP-PWD1> realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13
configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> admin-state unlocked
c. Delete configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> admin-state locked
configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> user-aor none user-name
none display-name none password none realm telkom.net.id no ac-code-prof no app-serv-prof
no ntwk-dp-prof
configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> voip-media-prof none
configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/voip
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile none
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 no bandwidth-profile
XGPON ALU 7360 ISAM Provisioning SOP 15
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3.3 B-2404-P ONT
3.3.1 TOPOLOGY
Figure 9 Physical topology of E1 SFP to B-2404-P ONT at PT. Telkom Indonesia
3.3.2 CONNECTIONS AND COMPONENTS
Figure 10 Physical connections for B-2404-P business ONTs
Table 5 B-2404-P business ONT connections
Connection Function
E1/T1 connections There are up to four E1/T1 ports supporting unstructured and fractional E1/T1 through RJ-48C connectors. Currently, E1 connections are supported while T1 connections are not.
Ethernet connections There are up to four Ethernet port supporting 10/100/1000Base-T Ethernet connections through Ethernet RJ-45 connectors.
PON optical connection This connection is provided through an SC/APC connector for the physical interface to the PON.
Power connection A terminal is provided to connect an external –12 V dc UPS to the ONT.
B-2404-P ONT
Splitter 1:8
Connection
FTM
7360 ISAM FX OLT
Splitter 1:4
PON
E1#1…4 E1 SFP
XGPON ALU 7360 ISAM Provisioning SOP 16
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 11 B-2404-P business ONT LEDs
Table 6 B-2404-P business ONT LED descriptions
Indicator Color Description
PWR
Green solid Green flashing slow Green flashing fast Red solid
Operating from AC power Operating from battery power System booting Battery low
GPON
Off Green solid Green flashing slow Red solid
Optical Not OK Optical OK; Ranged PON is in ranging and synchronizing process Optical Power Off (LOS/LOF)
DATA Off Green solid Green flash
Ethernet service is not configured in ONT Ethernet service is configured in ONT Ethernet service is configured and there is activity of receiving or transmitting data
CES
Off Green solid Green flashing
CES data path is not setup CES data path is ready LED blinks when links are up and there is activity (data receive and transfer). LED blinks with a 167 ms cycle and 50% duty cycle.
TIMING Off Green solid Green flashing
Reference clock is not valid Reference clock ready In holdover state
UPDATE Off Green flashing fast Red solid
Normal status Upgrading Upgrade failure
ALARM Off Green solid Red solid
Normal status No alarm with local Ethernet access enabled (for Telnet) Indicates hardware failure
POTS Off Green solid Green flashing fast
Telephone at POTS A and B are all in the on hook condition Telephone at POTS A and B are all in the off hook condition At least one POTS is in off hook condition for at least one hour
TEST Off Green solid Green flashing fast
Normal status ONT is under loopback test ONT is in normal state with local Ethernet access (for Telnet) enabled
XGPON ALU 7360 ISAM Provisioning SOP 17
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3.3.3 CREATE/MODIFY/DELETE ONT
a. Create configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sw-ver-pland 3FE54603AOCI35
sernum <ONT-SERNUM> subslocid WILDCARD voip-allowed enable cvlantrans-mode local
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up
configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/5 planned-card-type e1
plndnumdataports 4 plndnumvoiceports 0 admin-state up
b. Modify ONT S/N (Serial Number) configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sernum <NEW-ONT-SERNUM>
configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up
c. Delete configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down
configure equipment ont no interface 1/1/<SLOT>/<PON>/<ONT>
3.3.4 CREATE/DELETE E1 SERVICE
a. Create configure vlan id <VLAN-ID> mode cross-connect name <SERVICE-DESCRIPTION> in-qos-prof-name
name:Default_TC0
configure service customer <CUSTOMER-ID> description <CUSTOMER-DESCRIPTION>
configure service vpls <VLAN-ID> customer <CUSTOMER-ID> create
configure service vpls <VLAN-ID> description <SERVICE-DESCRIPTION>
configure service vpls <VLAN-ID> sap lt:1/1/<SLOT-ONT>:<VLAN-ID> create
configure service vpls <VLAN-ID> sap lt:1/1/15:<VLAN-ID> create
configure service vpls <VLAN-ID> user-user-com
configure service vpls <VLAN-ID> no shutdown
///SFP
configure ethernet line 1/1/15/<PORT> port-type uni admin-up
configure ethernet line 1/1/15/<PORT> mau 1 type 1000baselxfd power up
configure equipment sfpe1t1 clock lt: 1/1/15/<PORT> clocksource serdes
configure equipment sfpe1t1 pwtdm lt: 1/1/15/<PORT>:<E1-NUMBER> channel open packet-length
256 jitter-buff-size 7 vlanid <VLAN-ID> priority 6 conseq-number 2 ecid-rx <ECID-RX-DEC>
ecid-tx <ECID-TX-DEC> source-mac <SRC-MAC@> dest-mac <DEST-MAC@>
configure equipment sfpe1t1 framer lt: 1/1/15/<PORT>:<E1-NUMBER> frame-mode unframed
configure equipment sfpe1t1 liu lt: 1/1/15/<PORT>:<E1-NUMBER> distance longhaul cable-
impedance 120ohms
configure bridge port 1/1/15/<PORT> max-unicast-mac 10
configure bridge port 1/1/15/<PORT> vlan-id <VLAN-ID> tag single-tagged
// ONT
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/5/<PORT> admin-up
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> upstream-queue 0 bandwidth-profile
name:E1
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> queue [0...3] shaper-profile
name:E1
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> max-unicast-mac 10
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> vlan-id <VLAN-ID>
configure bridge port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> pvid <VLAN-ID>
configure ces ont profile <ID> profile-name <NAME> jitter-buff-max 100
configure ces ont line 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> mode unstructured frame unframed
encoding hdb3 line-length 120ohms
configure ces ont service 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> service-nbr 1 vlan <VLAN-ID>
timing-mode adaptive maintenance-prof 2 payload-size 256 transmit-ckt-id <TX-CKT-ID-HEX>
expected-ckt-id <DEST-CKT-ID-HEX> dest-mac-address <DEST-MAC@>
b. Delete configure bridge no port 1/1/15/<PORT>
configure equipment sfpe1t1 no pwtdm lt:1/1/15/<PORT>:<E1-NUMBER>
configure equipment sfpe1t1 no clock lt:1/1/15/<PORT>
configure ethernet line 1/1/15/<PORT> mau 1 power down
configure ethernet line 1/1/15/<PORT> no admin-up
configure ces ont no service 1/1/<SLOT>/<PON>/<ONT>/5/<PORT>
configure ces ont line 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> no admin-state
configure ces ont no profile <ID>
configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT>
configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/5/<PORT> no admin-up
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> queue [0...3] shaper-profile none
configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> upstream-queue 0 no bandwidth-
profile
configure vlan no id <VLAN-ID>
XGPON ALU 7360 ISAM Provisioning SOP 18
Sta
nd
ard
Op
era
tin
g P
roce
du
re
configure service vpls <VLAN-ID> shutdown
configure service vpls <VLAN-ID> sap lt:1/1/<SLOT>:<VLAN-ID> shutdown
configure service vpls <VLAN-ID> no sap lt:1/1/<SLOT-ONT>:<VLAN-ID>
configure service vpls <VLAN-ID> sap lt:1/1/15:<VLAN-ID> shutdown
configure service vpls <VLAN-ID> no sap lt:1/1/15:<VLAN-ID>
configure service no vpls <VLAN-ID>
configure service no customer <CUSTOMER-ID>
XGPON ALU 7360 ISAM Provisioning SOP 19
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3.4 POINT TO POINT (P2P) (NELT-B)
3.4.1 TOPOLOGY
Figure 12 Physical topology of P2P at PT. Telkom Indonesia
3.4.2 CONNECTIONS AND COMPONENTS
Figure 13 Front view of the NELT-B
Figure 14 Board LEDS on the NELT-B
Table 7 LED Definition for the NELT-B
LED Color Description
ALM Red Alert
A/S Green Active/Standby
PWR Green On line
7360 ISAM FX OLT
1 GbE SFP in NELT-B LT card
MSAN/SWITCH
XGPON ALU 7360 ISAM Provisioning SOP 20
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 15 LEDs for SFP Ports
Table 8 Behavior of LEDs for SFP Ports
Situation Status LED
Board reset Off
Link administrative down Off
Link administrative up and Loss Of signal (LOS) Off
Link administrative up and Signal detected On
Link is OK and carrying traffic Blinking
Figure 16 Physical of 1000Base-LX SFP
XGPON ALU 7360 ISAM Provisioning SOP 21
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Table 9 Optical parameters for Alcatel-Lucent approved optical modules
Part Number Description Wavelength Reach Operating
Temperature Optical Budget
Fiber mode
Gigabit Ethernet optical modules for optical connections
3FE 25774 AA 1 Gb/s Ethernet 1000Base-LX 1310 nm 10 km -40°C to + 85°C 11 dB SMF
Table 10 1000Base-LX optical module parameters
Parameter Minimum Typical Maximum
Absolute Maximum Ratings
Storage temperature -40°C - +85°C
Operating case temperature(1) -5°C - +85°C
Supply voltage 0V - +5.0V
Operating data rate - 1250 Mb/s -
Transmitter Performance Characteristics
Optical output power(2) -9.0 dBm - -3.0 dBm
TX wavelength 1260 nm 1310 nm 1360 nm
Center wavelength 1274 nm 1310 nm 1360 nm
Spectral width (-20dB) - - 4.0 nm
Extinction ratio 9 dB - -
Deterministic jitter - - 80 ps
Total jitter - - 227 ps
Relative intensity noise - - -120 dB/Hz
Transmitter output eye Compliant with IEEE 802.3z and FC-PI eye mask
Receiver Performance Characteristics
Operating data rate(4) - 1250 Mb/s -
Input optical power (10-12 BER)(2) -22.0 dBm - -3.0 dBm(5)
LOS thresholds, increasing light input - - -22.0 dBm
LOS thresholds, decreasing light input -30.0 dBm - -
LOS Hysteresis 0.5 dB - -
Deterministic jitter - - 170 ps
Total jitter - - 266 ps
Wavelength of operation 1100 nm - 1600 nm
Optical return loss 12 dB - -
Electrical 3 dB upper cut-off frequency - - 1500 MHz
Electrical 3 dB upper cut-off frequency Compliant with IEEE 802.3z standard
XGPON ALU 7360 ISAM Provisioning SOP 22
Sta
nd
ard
Op
era
tin
g P
roce
du
re
3.4.3 CREATE/MODIFY/DELETE TAGGED VLAN SERVICE
a. Create configure vlan id <VLAN-ID> mode cross-connect name <SERVICE-DESCRIPTION> in-qos-prof-name
name:Default_TC0
configure service customer <CUSTOMER-ID> description <CUSTOMER-DESCRIPTION>
configure service vpls <VLAN-ID> customer <CUSTOMER-ID> create
configure service vpls <VLAN-ID> description <SERVICE-DESCRIPTION>
configure service vpls <VLAN-ID> sap lag-1:<VLAN-ID> create
configure service vpls <VLAN-ID> sap lt:1/1/16:<VLAN-ID> create
configure service vpls <VLAN-ID> no shutdown
configure interface port ethernet-line:1/1/16/<PORT> admin-up
configure ethernet line 1/1/16/<PORT> port-type uni admin-up
configure ethernet line 1/1/16/<PORT> mau 1 type 1000baselx10 speed-auto-sense power up
configure bridge port 1/1/16/<PORT> max-unicast-mac 10
configure bridge port 1/1/16/<PORT> vlan-id <VLAN-ID> tag single-tagged
b. Delete configure bridge no port 1/1/16/<PORT>
configure ethernet line 1/1/16/<PORT> mau 1 no speed-auto-sense power down
configure ethernet line 1/1/16/<PORT> no admin-up
configure interface port ethernet-line:1/1/16/<PORT> no admin-up
configure service vpls <VLAN-ID> shutdown
configure service vpls <VLAN-ID> sap lag-1:<VLAN-ID> shutdown
configure service vpls <VLAN-ID> no sap lag-1:<VLAN-ID>
configure service vpls <VLAN-ID> sap lt:1/1/16:<VLAN-ID> shutdown
configure service vpls <VLAN-ID> no sap lt:1/1/16:<VLAN-ID>
configure service no vpls <VLAN-ID>
configure service no customer <CUSTOMER-ID>
configure vlan no id <VLAN-ID>
XGPON ALU 7360 ISAM Provisioning SOP 23
Sta
nd
ard
Op
era
tin
g P
roce
du
re
4. APPENDIX: PROVISIONING FLOW
Figure 17 Create ONT flow
Figure 18 Modify ONT serial number flow
Figure 19 Delete ONT flow
Figure 20 Create internet service flow (PPPoE)
1. SET UPSTREAM QOS INTERFACE
2. SET DOWNSTREAM QOS INTERFACE
3. UNLOCK INTERFACE PORT
4. CREATE BRIDGE PORT VLAN TRANS 881
5. SET PPPOE USERNAME
6. SET PPPOE PASSWORD
1. LOCK EQUIPMENT ONT INTERFACE
2. DELETE EQUIPMENT ONT INTERFACE
1. LOCK EQUIPMENT ONT INTERFACE
2. MODIFY EQUIPMENT ONT INTERFACE
2. UNLOCK EQUIPMENT ONT INTERFACE
1. CREATE EQUIPMENT ONT INTERFACE
2. UNLOCK EQUIPMENT ONT INTERFACE
3. CREATE EQUIPMENT ONT SLOT
XGPON ALU 7360 ISAM Provisioning SOP 24
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 21 Modify service bandwidth flow
Figure 22 Modify internet PPPoE username and password flow
Figure 23 Delete internet service flow (PPPoE)
Figure 24 Create internet service flow (Bridge)
1. DELETE PPPOE PASSWORD
2. DELETE PPPOE USERNAME
3. DELETE BRIDGE PORT
4. LOCK INTERFACE PORT
5. DELETE DOWNSTREAM QOS INTERFACE
6. DELETE UPSTREAM QOS INTERFACE
1. MODIFY PPPOE USERNAME
2. MODIFY PPPOE PASSWORD
1. MODIFY UPSTREAM QOS INTERFACE
2. MODIFY DOWNSTREAM QOS INTERFACE
1. SET UPSTREAM QOS INTERFACE
2. SET DOWNSTREAM QOS INTERFACE
3. UNLOCK INTERFACE PORT
4. CREATE BRIDGE PORT UNTAGGED VLAN
XGPON ALU 7360 ISAM Provisioning SOP 25
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 25 Delete internet service flow (Bridge)
Figure 26 Create IPTV service flow
Figure 27 Delete IPTV service flow
1. SET UPSTREAM QOS INTERFACE
2. SET DOWNSTREAM QOS INTERFACE
3. UNLOCK INTERFACE PORT
4. CREATE BRIDGE PORT UNTAGGED VLAN
5. CREATE IGMP CHANNEL
1. DELETE BRIDGE PORT
2. LOCK INTERFACE PORT
3. DELETE DOWNSTREM QOS INTERFACE
4. DELETE UPSTREAM QOS INTERFACE
1. DELETE BRIDGE PORT
2. LOCK INTERFACE PORT
3. DELETE DOWNSTREAM QOS INTERFACE
4. DELETE UPSTREAM QOS INTERFACE
XGPON ALU 7360 ISAM Provisioning SOP 26
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 28 Create voice service flow
Figure 29 Modify POTS port flow
Figure 30 Delete voice service flow
1. SET UPSTREAM QOS INTERFACE
2. SET DOWNSTREAM QOS INTERFACE
3. CREATE BRIDGE PORT UNTAGGED VLAN
4. CREATE IPHOST
5. CREATE VOICE ONT VOIP-CONFIG
6. CREATE VOICE ONT SIP-CONFIG
7. CREATE VOICE ONT VOICE-SIP-PORT
8. CREATE VOICE ONT VOICE-PORT & UNLOCK
1. LOCK VOICE ONT POTS
2. MODIFY VOICE ONT VOICE-SIP-PORT
3. UNLOCK VOICE ONT POTS
1. LOCK VOICE ONT POTS
2. MODIFY VOICE ONT VOICE-SIP-PORT
3. MODIFY VOICE-ONT VOICE-PORT
4. DELETE BRIDGE PORT
5. DELETE UPSTREAM QOS INTERFACE
6. DELETE DOWNSTREAM QOS INTERFACE
XGPON ALU 7360 ISAM Provisioning SOP 27
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 31 Create E1 service flow
1. CREATE IACM VLAN
2. CREATE SERVICE CUSTOMER
3. CREATE SERVICE VPLS
4. UNLOCK INTERFACE PORT ETHERNET-LINE
5. SET ETHERNET-LINE MAU TYPE AND UNLOCK
6. CREATE SFPE1T1 CLOCK
7. CREATE SFPE1T1 PWTDM
8. CREATE SFPE1T1 FRAMER
9. CREATE SFPE1T1 LIU
10. CREATE BRIDGE PORT ON SFP E1 IN NELT-B CARD
11. UNLOCK INTERFACE PORT ON ONT
12. SET UPSTREAM QOS INTERFACE
13. SET DOWNSTREAM QOS INTERFACE
14. CREATE BRIDGE PORT UNTAGGED VLAN
15. CREATE CES ONT PROFILE
16. CREATE CES ONT LINE
11. CREATE CES ONT SERVICE
XGPON ALU 7360 ISAM Provisioning SOP 28
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 32 Delete E1 service flow
1. DELETE BRIDGE PORT
2. DELETE EQUIPMENT SFPE1T1 PWTDM
3. DELETE EQUIPMENT SFPE1T1 CLOCK
4. REMOVE ETHERNET LINE MAU TYPE AND LOCK
5. DELETE CES ONT SERVICE
6. DELETE CES ONT LINE
7. DELETE CES ONT PROFILE
8. DELETE ONT BRIDGE PORT
9. LOCK ONT INTERFACE PORT
10. DELETE DOWNSTREAM QOS INTERFACE
11. DELETE UPSTREAM QOS INTERFACE
12. DELETE IACM VLAN
13. DELETE SERVICE VPLS
14. DELETE SERVICE CUSTOMER
XGPON ALU 7360 ISAM Provisioning SOP 29
Sta
nd
ard
Op
era
tin
g P
roce
du
re
Figure 33 Create point to point tagged vlan flow
Figure 34 Delete point to point tagged vlan flow
1. CREATE IACM VLAN
2. CREATE SERVICE CUSTOMER
3. CREATE SERVICE VPLS
4. UNLOCK INTERFACE PORT ETHERNET-LINE
5. SET ETHERNET-LINE MAU TYPE AND UNLOCK
6. CREATE BRIDGE PORT TAGGED VLAN
1. DELETE BRIDGE PORT
2. REMOVE ETHERNET-LINE MAU TYPE AND LOCK
3. LOCK INTERFACE PORT ETHERNET-LINE
4. DELETE SERVICE VPLS
5. DELETE SERVICE CUSTOMER
6. DELETE IACM VLAN